Home > Pedal Board Parts / DIY > Most Popular Parts & Kits
Look kids, it’s been a minute since you cleaned that board up and chase down those ghosty cable noises. Let’s get Spring Cleaning’! Below you’ll find the finest selection of DIY Parts for your springtime clean up and mod fest!
  1. Clean Slate: It’s time to pull all those sweet pedals off and re organize. We find it helpful to use a small, steel ruler, butter knife or credit card to separate the velcro.
  2. Clean Up: Vacuum the deck, blow the cracks out with an air compressor (or dust off) and wipe everything down. We find it useful to use a large, soft bristled paint brush for getting into cracks and removing the crud between the knobs of our pedals.
  3. Cable Check: Start by wiping all your cables down (especially your nasty ass instrument cables). Windex or denatured alcohol works great for this. Just spray some on a rag and run the cable through the rag (squeezing it in your off hand). If you want to be sure you’re getting the best connection, use steel wool to clean the tips of all of your patch cables. All metal alloys will eventually oxidize (corrode). This oxidized layer builds up resistance and deaden’s your signal or worse, cause a faulty connection. Simple take a ball of steel wool, pinch the tip of the cable with it and spin it back and forth a few times. This will knock off any oxidization and minimize resistance.
  4. Due Diligence: If you’re REALLY gonna get disciplined about it, use a cable tester or Ohm meter to test each cable for continuity and resistance (or just plug it in and see if it works).
  5. Re Assembly: Lay out your pedals first. If you have a large board, it’s sometimes best to put tape down in the same configuration of your deck. Lay the pedals out in this so you can look at them and make sure everything will fit. Simply transfer each pedal to the board and securely fasten it.
  6. Wiring: We like to run power cables first. They tend to be thinner and lay easily under the instrument cables. It’s often possible to push them under the edge of a pedal making them almost invisible. Once you have your power run, plug in your patch cables. There are a zillion different varieties and ways of doing things, to learn more about the most common styles here.
  7. Testing: Plug it all in and let her rip! If you you’re not getting signal passing through don’t freak out. Simply work back from the last pedal in the chain, you’ll find the issue.
Sort By:
1
Pedalboard Master Kit for the ultimate DIY enthusiast
Do It Yourself - Pedalboard Master Builder Kit
List Price: $107.85
Our Price: $90.00
Savings: $17.85

This master builder kit has our most frequently purchased items in one spot with configurable options. Customize to your specs by choosing optional features from each different component in the package via the drop down menu's

***International Orders***
Everything outside the US. We cannot ship flammable contents out of the US, make sure you select the NONE option for spray glue before checking out. If you don't the order will ship WITHOUT the adhesive anyway ;-D


***International Orders***
Anyone outside of the 110-120 Volt range, please do not select the Indicator lamp option within the "Electrical Input" drop down menu, our bulbs are only rated at 110-120V operation. Sorry, I'm working on getting something compatible...

***Please NOTE: when choosing the power wiring harness options, notice there are 6 choices. If you want a version WITH the indicator lamp and/or toggle switch, make sure you select the appropriate version. Even when selecting an option that doesn't include the indicator lamp, the choice for choosing the indicator lamp color will still be present.***

  • Super Loop top deck material in various sizes ($12)
  • Half Can Super Spray Adhesive($8)
  • 2 Feet Super Hook Pedal Side Material ($6)
  • 2 audio harness' with your choice of either (2) two black locking Neutrick 1/4" or Tele Jacks with 18" soldered Mogami cable and Switchcraft 228 pancake plugs ($38)
  • (1) one IEC 5-15 or 3 Prong Male Edison AC power inlet wiring harness with pedal power supply pigtail. Configure these with OPTIONAL Carling master ON/OFF toggle switch, & OPTIONAL Fender style jewel lamp assembly with LED bulb with your choice of colored lens ($14.50)
  • (1) 6' 18AWG IEC power cable ($12)
  • (4) 2 Hole Mounting Brackets ($3.40)
  • Rack Handles in Silver or Black ($4.75)
  • (4) 1" Rubber Feet w/ hardware ($3.20)
  • 1 Set of 20 Cable Clamps and Screws at 1/4" & 1/2" ($6)

$107.85 if purchased separately.

When we build the wiring harness, the indicator lamp wires and toggle switch wires are also soldered onto the IEC connector. We then hot glue the soldered part of the assembly for safe operation. Please let us know if you need a longer run of the indicator lamp wire in the notes section at checkout.

Do you need additional audio harness'?
Instructions Located on our Download Page.
Electronics Kit for DIY, featuring beautifully crafted power and audio harness'!
Do It Yourself - Pedalboard Electronics Kit 3
List Price: $107.00
Our Price: $89.99
Savings: $17.01

Kit 3 uses a 110-120V indicator lamp assembly, if you are operating outside of this voltage, this kit WILL NOT work for you. Check out our Basic & Kit 2 for international usage.

2 audio harness' with your choice of either (2) two black locking Neutrick 1/4" or Tele Jacks with 18" soldered Mogami cable and switchcraft pancake plugs or mini straight connectors ($38.00) (1) one IEC 5-15 or 3 Prong Male Edison AC power inlet wiring harness with a Carling master ON/OFF toggle switch, & 1 Fender style jewel lamp assembly with LED bulb and your choice of lens color($69.00).

$107.00 if purchased separately.

When we build the wiring harness, the indicator lamp wires and toggle switch wires are also soldered onto the IEC connector. We then hot glue the soldered part of the assembly for safe operation. Please let us know if you need a longer run of the indicator lamp wire in the notes section at checkout.

Do you need additional audio harness'?
Instructions Located on our Download Page.
Pedalboard master wiring harness: power supply, indicator light and power input
Electrical Harness for Toggle/Indy Light & Pedal Power Device
Our Price: $69.00

Our most popular power harness: a multi-function, fully complete wiring harness with AC power in, master On/Off toggle, indicator lamp and pedal power supply hookup. Soldered & tested for an easy installation as well as reliable high quality service. The assembly includes either an 5-15 IEC power input connector or 3 blade Edison style plugin, both used to plug in wall power. Cable leads are then soldered to a Carling master ON/OFF power switch & indicator lamp assembly. A 12" power cord is pig-tailed in allowing you to power most pedal powering devices. This harness ONLY works at 110V, so if your in the US, Mexico and Canada, your good to go! Includes all mounting hardware and download instructions below.

If you need a custom harness made, please give us a call and we will accommodate...

We seal and heat shrink all the solder points. If you need extra length of cable for the Indy lamp, power switch or pigtail let us know in the comment section during checkout. There MAY be an additional charge...

Instructions Located on our Download Page.

Grab an IEC Power Cable offered at different lengths.

Electronics Kit for DIY pedalboard
Do It Yourself - Pedalboard Electronics Kit Basic
List Price: $52.50
Our Price: $45.75
Savings: $6.75

Your choice of (2)two Tele Jacks or for 4.00 more, 2 Black Locking Neutrick jacks soldered to Mogami and Switchcraft pancake right angle or straight plugs ($38.00) and (1) one IEC 5-15 or 3 Prong Male Edison AC power inlet wiring harness with($14.50). $52.50 if purchased separately.

  • The AC power IEC is rated for 110-250 Volts so this is compatible world wide.
  • The Edison plug is only rated for 125Volts USA, Canada and Mexico usage ONLY!
Do you need additional audio harness'?
Instructions Located on our Download Page.
Pedalboard XLR Audio Input/Output Harness
Pro Audio Harness XLR For Vocal Effects and Direct Box - DIY
Our Price: $32.00

This item is per 1 assembly. If you need 2, then you need to order 2.

Easily add a very useful function to your pedalboard with this pre-wired and customizable assembly. This professional grade XLR audio harness is a complete assembly soldered and tested for years of service. This assembly includes one (1) of your choice of Nuetrik male or female panel mount XLR interface for the pedalboard side. Soldered Mogami Negflex 2534 lead cable attached to either a straight or adjustable right angle male or female XLR connector. These can streamline your pedalboard, integrating a vocal signal into your board with a completely separate signal path, adding balanced direct out functionality for live or recording situations.

All hardware is included to complete this easy DIY installation.

Instructions Located on our Download Page. See "cable Lead Installation and use the D Square/Panel Mount method of installation.
Velcro Pedalboard Top Kit for DIY pedalboard
Do It Yourself - Pedalboard Deck Kit
List Price: $27.50
Our Price: $24.50
Savings: $3.00

***This kit has to be shipped via Ground Shipping because flammable contents can't be air shipped. During checkout, use the Ground Shipping option. This product isn't available for any international shipments at this time***

Choose from many popular sizes of West Coast Pedal Boards exclusive Super Loop pedalboard deck material(starting at $13.00), 1/2 can of our super sticky, high temp rated spray contact adhesive ($8.75) and 2 Rack Handles with mounting hardware($4.75). $27.50 if purchased separately... Written and Video Instructions Available

Instructions Located on our Download Page.

http://youtu.be/t9Lo6l2TtSg
Pedalboard Audio Input/Output Harness
Pro Audio Harness For Guitar In, Out, FX Loop - DIY
Our Price: $23.00
Sale Price: $19.00
Savings: $4.00

This item is per 1 assembly. If you need 2, then you need to order 2.

When choosing the stereo version of this cable, we will use Mogami 2552 cable and a Switchcraft right angle 236

Easily add a very useful function to your pedalboard. This audio wiring harness is a complete assembly soldered and tested for seamless and professional results. If you want to add any type of audio interface, we use high quality parts, materials and assembly techniques. The assembly includes one (1) of your choice tele style(chrome, black or gold) jack plate with switchcraft input jack, or black locking Neutrick input jacks. The mono version has a Switchcraft 228 right angle pancake connector. These can be used to feed your first pedal, or as an output from your last pedal to feed your amp(s). It also can be used for other signal routing function such as FX LOOPS etc. These can be made in a stereo cable version as well; most commonly used for integrating your amp switching capabilities onto the board.

All lead cable is high fidelity Mogami cable, used on all of our Standard Series and Custom Shop West Coast Pedalboards.

All hardware is included to complete this easy DIY installation.

Instructions Located on our Download Page.
Pedalboard AC wiring harness
Pedalboard Power Supply Harness 110-250Volts
Our Price: $14.50

Our wiring harness is a complete assembly. Pedalboard side has a 5-15 IEC connector or optional recessed male Edison plug (used to plug in wall power) with a 16" pigtail that can power many different power supplies. Operates worldwide at 110-250Volts. Includes all mounting hardware.

Did you know that we can make these harness' to work with any power supply on the market? 707.836.7440

Grab an IEC Power Cable offered at different lengths.


Instructions Located on our Download Page.

The best pedalboard velcro deck material ever!!
Pedal Board Carpet - A West Coast EXCLUSIVE - Super Loop
Our Price: $13.50

West Coast Pedalboards Super Loop is the premier pedalboard deck material, boasting excellent adherence, NEVER looses grip and.... it NEVER frizzes. Extreme durability even at the Pro touring level.... We sell A ton of the 12",17", 21", 23" and 28" width's, but can go as wide as 60 inches & various lengths. If you need a piece that is larger than what is listed, call or email your dims. If your look ing for a piece that in-between 2 of the sizes, choose the larger size and you'll be able to cut it down after installation. Inferior materials can look the same but ours has a lifetime no frizz guarantee! Our Super Loop is the most reliable loop material in the industry. Install with a high tack spray contact adhesive like this and never worry about loose pedals again!

James had this to say about it, and I quote, "Super loop from west coast pedalboard. Just had mine today... It's the fucking tits." So there ya have it folks...

Instructions Located on our Download Page.
Pedalboard AC Power in - Recessed Flanged Inlet
AC Power Male Inlet - 125Volt MAX 15Amp
Our Price: $10.25

AC power input port for adding juice to your pedalboard.  Cable lead is not included in this super easy to install, solder less power solution.
Dual-Lock Low Profile Pedalboard 3M
Pedalboard Velcro Dual Lock 250 - Pedal Fastener
Our Price: $8.00

This super duty material is used primarily on boards where ultra secure pedal placement is desired. 3M Dual Lock 250 is a universal fastener that will go on the pedal side & the pedalboard deck. Dual Lock WON'T work on, or with our Super Loop deck top material, but will work on our poly top decks, under side of boards to secure pedal power devices and other pedal boarding gear. When installed properly, this product is extremely grippy. This particular Dual Lock is 1" wide, 250 mushrooms per sq/inch & is adhesive backed. Perfect for pedals, controllers, pedal power devices and any other devices that can be placed on a pedalboard. Instructions NOT Included...!
Hook side self adhesive velcro for pedal fastening
Pedalboard Velcro - Pedal Fastener - Super Hook
Our Price: $7.00

Our Super Hook is industrial strength. When properly adhered to the backs of your pedals, this will be a truly lasting solution. When used in conjunction with our Super Loop deck material, you'll experience pedal grip like never before. The main reason these products work so well together, is the hook and the loop material are paired up to work with each other perfectly. This material is 1" wide, and split down the center making two .5" wide strips. Available in 2,4,6,8,10 and 12 foot sections.

Perfect for pedals, controllers, pedal power devices and any other devices that can be placed on a pedalboard.

How much do I need? Since the material is split into two sections, a 2 foot piece equals 4' of .5" wide material. When installing, we always install 2 strips on the longest side of the pedal/device. The 2 foot section will cover 4 pedals that are 6" on the longest side.

***Make sure the pedal surface area is clean of any debris, including previously installed velcro type products. Make sure that any obstructions such as rubber backing (found on Boss pedals) and rubber feet are removed. This product works best when its adhered to metal; heating it gently with a heat gun can also increase the adhesive backed grip quality. Avoid installing when the pedal or device is cold, we've found that 60-80 degrees is ideal. Also avoid covering screws & screw holes. You won't need much when installed properly; we usually put 1 strip down each of the longest sides of the pedals***
Pedalboard hinges and screws
Lift Off Hinge Set w/ Hardware
Our Price: $6.25

These black lift off hinges come in a set of 2 and include eight(8) 5/8" screws. They measure 2.25" at the widest point, and 1.75" at the tallest.  These are the PERFECT solution if you want a cased board.  Instructions are NOT included..
Pedalboard wire clamp kit for the ultimate in pedalboard cable management.
Pedalboard Screw & Cable Management Clamp Kit
Our Price: $6.25

This kit comes with a variety of twenty (20) 1/4" & 1/2" black plastic cable clamps and black 1/2" truss screws. These are perfectly useful for securing pedal power and patch cables to the pedalboard. Allows a professional and clean installation for the ultimate in pedalboard cable management.

Instructions are NOT included.
Pedalboard Case Latch Kit in Chrome
Pedalboard & Case Latch Kit
Our Price: $6.00

These chrome 2 piece latches are ready for duty. We use these for many of our flat series boards & cases. These come in a set of 2 with #6 5/8" chrome pan head screws. As always, INSTRUCTIONS NOT INCLUDED!!
Chrome Rack Handles with hardware
Rack Handles
Our Price: $4.75

All handles come with appropriate hardware to complete installation.
Mounting brackets for pedal power supplies
Pedalboard Power Supply Brackets
Our Price: $4.25

Mount all Voodoo Lab and T-Rex Fuel Cell, Supa-Charger power supplies to any West Coast Pedalboard
Pedalboard AC Power in IEC port
IEC 5-15 Male AC Inlet 120-250 Volts
Our Price: $2.25
Sale Price: $1.75
Savings: $0.50

IEC port to add AC power input function to your pedalboard. Add some juice to your pedalboard quickly and easily.  Soldering and a cable lead will be required to complete this super easy DIY project.
Pedalboard feet and screws
Non Slip Rubber Feet
Our Price: $0.82

These are non slip,1" and 1.5" diameter by 3/8" height rubber pedalboard feet.  Steel washers built into the feet allow a very secure mounting platform for those who like quality components.  Each piece includes one black 5/8" truss screw. These work great for pedalboards and pedal board cases! Instructions NOT included..!
Pedalboard brackets and screws
2 Hole Bracket
Our Price: $0.75

These black brackets are 1.25" long, .5/8" wide and include (2) 1/2" truss screws. They are an excellent choice for stabalizing the pedalboard deck.  We also use these as additional support for our flat series cases and light duty cases. Use 4 or more brackets depending on how big your board or case is.  Instructions NOT included.
Solder your own custom pedalboard patch cables with this custom pedalboard cable kit.
Pedalboard Patch Cable DIY Pack

When reliability is crucial; soldered Mogami cable, Switchcraft and GnH jacks will give you peace of mind. The components provided to construct your custom set of cables are chosen for quality, industry standard recognition, durability, reliability and function. The assembly is really easy, and when done properly, will provide many years of reliable service!

Choose the cable quantity, jack orientation & quantity. Each jack purchased also includes a piece of 1/2" heat shrink tubing, except the GnH mini right angle VLP's.

If you need a random number, or different jack orientation, here are separate links to each individual item for individual quantity purchase. Allowing you further customization of your kit.

If you have any other questions, or need something that isn't listed, call 707.836.7440 to talk with Spence...

   
 
1
Copyright ©  West Coast Pedal Board. All Rights Reserved.
Built with Volusion